Problems with all timeframes in futures ES, NQ, MES, and MNQ

General Discussions
1

Market had to start 11/02/2025 at 17:00.

Only X seconds charts are giving the correct time.

All timeframes 1 minute or higher are giving 18:00.

So all charts except second charts give wrong times.

2

What session time are you running in DataSeries?

3

CME US Index Futures ETH
Same problem for ES, NQ, MES,MNQ, M6E
I added below a chart with MNQ 12-25.
First chart shows in 1 panel 1 minute chart and 60 seconds chart. You see that 60 seconds has correct time, but 1 minute chart starts only at 18:00.
The second chart shows that the quotes are everywhere correct, but the time frame skips one hour in all charts bigger than XXX seconds.
So charts in seconds are correct, charts in minutes are all wrong.
The problem started at the opening today at 17:00. I think it has something to do with changing from summer to winter time.
I deleted in db: cache, tick, minute and day and restarted the program. Problem is still there.

2025-11-03 00_58_29-Chart - MNQ 12-25
2025-11-03 00_58_29-Chart - MNQ 12-251990×1220 121 KB

4

Around 18:30, all my charts give already values for minute indicators for 19:00. LOL.
So the charts show the actual values already for the future.
Nobody else has this problem???

5

I checked MNQ 12-25 and I see that ALL the open, high, low, close and volume are WRONG.

Between 17:00:00 and 18:59:59 on 11/02/2025, not a single quote is correct. At 19:00:00 suddenly all the quotes were correct again. But the period between 17:00:00 and 18:59:59 on 11/02/2025 is still wrong. So it is clearly a problem from NT8 as I did not touch my computer after 18:00:00 anymore. If it had been my computer, the problem would still exist, as my computer cannot fix that problem without me doing something.

I checked MES 12-25, and M6E 12-25 also, and see the same problem. ALL the open, high, low, close and volume are WRONG for that same period.
This means that if you use these wrong quotes in indicators (like EMA for 6 hours), all your indicators give wrong values in the period AFTER 18:59:59 on 11/02/2025.
It is also very strange that after 19:00:00 the synchronization between minutes, and seconds data was restored, without however fixing the error for the past.

6

Do you have daylight savings time enabled as it switched yesterday

7

I made three charts:

  1. 15 minute
  2. 1 minute
  3. 15 seconds
    Result:
  4. 15 minute chart has wrong time and wrong data
  5. 1 minute chart has wrong time and wrong data
  6. 15 seconds time is correct and data is correct

Next step: I changed the 1 minute chart in a 60 second chart (which is identical as 1 minute equals 60 seconds)
Result:

  1. 15 minute chart has wrong time and wrong data
  2. 60 second chart has correct time and data is correct
  3. 15 seconds chart has correct time and data is correct

There are two possibilities:

  1. Time settings are correct: all charts have the correct time and data is correct
  2. Time settings are wrong: all charts have the wrong time and data is wrong

But what is the reality:

  1. Minute charts are wrong and data is wrong
  2. Seconds charts are correct and data is correct

That is impossible; all charts should be correct or wrong. Which is never the case. So the problem is not the time settings.
And what makes it completely crazy: without touching anything, after 2 hours all charts had the correct time and correct data. But past data was not corrected, so still wrong.